American Petroleum Institute (API) Fourth Edition, June 1995. 74p. This standard covers the minimum requirements for special-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and reducers of parallel-shaft design for refinery services.
American Petroleum Instltute (API) Fourth Edition, April 1999. 240p. This international standard covers the minimum requirements for lubrication systems, oil-type shaft-sealing systems, dry gas face-type shaft-sealing systems, and controloil systems for general or special purpose applications
American Petroleum Institute (API) Temth Edition, February 2002. 196p. This standard is based on the accumulated knowledge and experience of purchasers and manufacturers of welded, low-pressure oil storage tanks of various sizes and capacities for internal pressures not more than 15 pounds per square inch gauge. The object of this publication is to provide a purchase specification...
American Petroleum Institute (API). Draft. First Edition. 29p. This standard specifies the requirements for a heavy-duty series of bolted bonnet steel globe valves for petroleum refinery and related applications where corrosion, erosion and other service conditions would indicate a need for heavy wall sections and large stem diameters.
American Petroleum Institute (API) Temth Edition, November 1998. Addendum 2, November 2001. 240p. This standard covers material, design, fabrication, erection, and testing requirements for vertical, cylindrical, aboveground, closed- and open-top, welded steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal pressures...
American Petroleum Institute (API) Temth Edition, November 1998. Addendum 3, September 2003. 280p. This standard covers material, design, fabrication, erection, and testing requirements for vertical, cylindrical, aboveground, closed- and open-top, welded steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal...
American Petroleum Institute (API) Eleventh Edition, June 2007. 394p. This Standard establishes minimum requirements for material, design, fabrication, erection, and testing for vertical, cylindrical, aboveground, closed- and open-top, welded carbon or stainless steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal...
American Petroleum Institute (API) Second Edition, December 2010. 96p. This standard contains practices for isolating potential flow zones, an integral element in maintaining well integrity. The focus of this standard is the prevention of flow through or past barriers that are installed during well construction
American Petroleum Instltute (API) Fourth Edition, April 2009. 166p. This standard covers steel storage tanks built to API 650 and its predecessor API 12C. It provides minimum requirements for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, and reconstruction.
An American National Standard, American Petroleum Institute (API). Eighth Edition, August 2007. 52p. This International Standard specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries
An American National Standard, American Petroleum Institute (API). Fifth Edition, March 2002. 126p. This API standard is identical with English version of ISO
13706. This Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and...
American Petroleum Institute (API) Third Edition, September 1996. 87p. This standard establishes the minimum requirements for constant-speed, packaged, integrally geared centrifugal air compressors, including their accessories.
American Petroleum Institute (API) Second Edition, July 1997. 90p. This standard covers the minimum requirements for general-purpose, enclosed single and multistage gear units incorporating parallel shaft helical and right angle spiral bevel gears for the petroleum, chemical, and gas industries
American Petroleum Institute (API). First Edition. Draft Dated 04.23.2014. 67 p. The scope of this technical report is for the design evaluation of oil and gas subsea equipment utilized in high-pressure high-temperature (HPHT) environments. For the purpose of the technical report, HPHT environments are intended to be one or a combination of the following well conditions: 1) The...
American Petroleum Instltute (API), 2005. 58 p. The objective of this document is to provide general guidance to owners and operators of U.S. domestic petroleum assets for effectively managing security risks and provide a reference of certain applicable Federal security laws and regulations that may impact petroleum operations. Domestic petroleum assets are widely distributed,...
American Petroleum Instltute (API). 2011. 30 p. Hydraulic Fracturing Technology. Hydraulic fracturing is a technology that was developed in the 1940s and has been continuously improved upon since that time. It has been used in more than one million wells across the U.S., and it has helped produce more than 600 trillion cubic feet of natural gas and 7 billion barrels of oil. The...
American Petroleum Institute (API) and The Institute of Petroleum, London (IP). Fifth Edition, July 2002. 50p. ISBN: 0 85293 371 1This publication specifies the minimum performance and mechanical requirements and the testing and qualification procedures for aviation jet fuel filter/separators with flow rates ranging up to 9 500 lpm (2 500 gpm). This specification defines...
American Petroleum Institute (API) and The Institute of Petroleum, London (IP). February 2001. 50p. ISBN: 0 85293 282 0. This publication specifies the minimum requirements for a filter/separator system to qualify to API/IP 1581 by similarity. This publication applies to two-stage (filter and separator) and the filter/separator stages of multi-stage filter/separator systems....
American Petroleum Institute (API) and The Institute of Petroleum, London (IP). Third Edition, April 2001. 49p. ISBN: 0 85293 280 4. This publication specifies dimensions, coupling action, activation, and other requirements to achieve the necessary operational requirements and full interchangeability between components from manufacturers of hydrant pit valve assemblies and...
Technomic Publishing Company, Inc., Lancaster, Pennsylvania, U.S.A. 2000. 253 р. ISBN: No. 1-56676-832- 2. This book is about "Engineering Economics" which is a subset of microeconomics. It covers the economics and financial analyses needed to assess the viability of projects and to choose the best among many. As such it is relevant not only to engineers but also to anyone who...
Australian/New Zealand Standard. Originated in Australia as part of AS 2063-1977. Originated in New Zealand as NZS 5439:1986. Previous edition AS/NZS 2063: 1996. Second edition 2008. Reissued incorporating Amendment No.1 (December 2009). 22 p. This Standard specifies construction requirements and the basic performance requirements for impact energy attenuation, helmet stability,...
An American National Standard. The American Society of Mechanical Engineers (ASME). Date of Issuance: June 15, 2004. Revision and Consolidation of ASME A112.19.2M-1998 and ASME A112.19.6-1995. 71p.This Standard establishes requirements and test methods pertaining to materials, significant dimensions, and functional performance for vitreous china plumbing fixtures. The sanitary...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME A13.1-1996 (R2002). Date of Issuance: April 4, 2007. 10 p. This Standard is intended to establish a common system to assist in identification of hazardous materials conveyed in piping systems and their hazards when released in the environment. This Standard is intended to...
An American National Standard. The American Society of Mechanical Engineers (ASME). Canadian Standards Association (CSA). Revision of ASME A17.1-2004 and CSA B44-04. 455p. This Code covers the design, construction, operation, inspection, testing, maintenance, alteration, and repair of the following equipment and its associated parts, rooms, spaces, and hoistways, where located...
An American National Standard. The American Society of Mechanical Engineers (ASME). Canadian Standards Association (CSA). Date of Issuance: December 30, 2009. 216p. Revisions being made in this Addenda are identified by a margin note, (b). Changes made to correct errors in A17.1-2007/CSA B44-07, as well as other new editorial changes, are identified by (ED). Revision designators...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME A17.3-2005. Date of Issuance: January 9, 2009. 119p. This Code of safety standards covers existing elevators, escalators, and their hoistways (except as modified by 1.1.2). There are specific requirements for existing installations in this Code that could differ from those found...
An American National Standard. The American Society of Mechanical Engineers (ASME). Date of Issuance: December 20, 1999. Errata to ASME A17.4-1999. September 2002. 42p. This guide was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the guide was balanced to assure that individuals from competent...
An American National Standard. The American Society of Mechanical Engineers (ASME). Canadian Standards Association (CSA). Date of Issuance: December 2004. 82p. The requirements of this Standard apply to the following electrical equipment for elevators, escalators, moving walks, dumbwaiters, material lifts, and elevating devices for persons with physical disabilities (platform...
An American National Standard. The American Society of Mechanical Engineers (ASME). Date of Issuance: July 30, 2010. 54p. This Standard covers the means and members of suspension, compensation, and governor systems for elevators within the scope of ASME AI 7.I/CSA B44. This Standard includes the material properties, design, testing, inspection, and replacement criteria for...
An American National Standard. The American Society of Mechanical Engineers (ASME). Canadian Standards Association (CSA). Date of Issuance: March 2007. 139p. This Code covers the design, construction, operation, inspection, testing, maintenance, alteration, and repair of the following equipment and its associated parts, rooms, spaces, and hoistways, where located in or adjacent...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME A18.1-2005. Date of Issuance: August 28, 2008. 76p. This safety Standard covers the design, construction, installation, operation, inspection, testing, maintenance, and repair of inclined stairway chairlifts and inclined and vertical platform lifts intended for transportation of a...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B1.10М-1997. Date of Issuance: March 5. 2004. 28 p. This Standard specifies the thread form, series, tolerance, and designation for the Unified Miniature Screw Threads. The series covers a diameter range of 0.30 mm to 1,40 mm, extending the metric M-Profile and unified thread...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B1.1-1989 (R2001). Date of Issuance: September 30, 2004. 190 р. This Standard specifies the thread form, series, class, allowance, tolerance, and designation for unified screw threads. (In order to emphasize that unified screw threads are based on inch modules, they may be denoted...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B1.12-1972. Date of Issuance: November 15, 1987. 68 p. This Standard provides dimensional tables for external and internal plastic flow interference-fit (Class 5) threads of modified National thread form in the coarse thread series (NC) in sizes 0.250 in. through 1.500 in.
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B1.13M-2001. 82p. This Standard contains general metric standards for a 60 deg symmetrical screw thread with a basic ISO 68-1 profile designated M profile. The M profile threads of tolerance class 6H/6g are intended for metric applications where inch class 2A/2B have been used. At...
American Society of Mechanical Engineers (ASME) .1995. Errata to ASME Bl.15-1995, March 1997. 68р. This Standard establishes the basic triangular profile for the UNJ thread form, provides a system of designations, lists the standard series of diameterpitch combinations for diameters from 0.600 to 6.000 in., and specifies limiting dimensions and tolerances.
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ANSI B1.16М-1972. Date of Issuance: April 30,1985. 174 p. This Standard provides essential specifications and dimensions for the gages used on M series metric screw threads, and covers the specifications and dimensions for the thread gages and measuring equipment listed in Tables 1 and...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ANSI B2.1-1968. Date of Issuance: Augustl 31,1983. 32 p. This American National Standard covers dimensions and gaging of pipe threads for general purpose applications. The types of pipe threads included in this Standard are designated by specifying in sequence the nominal pipe size,'...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ANSI B1.20.5-1978. Date of Issuance: March 15, 1991. Reaffirmed 2004. 63 p. The scope of this Standard is to provide information regarding practical dryseal thread inspection methods and commonly used gages for production evaluation purposes. All dimensions are in inches unless...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ANSI/ASME B1.20.7-1966. Date of Issuance: April 16,1992. 24 p. The purpose of this document is to provide standards for application to the threaded parts of hose couplings, valves, nozzles, and all other fittings used in direct connection with hose intended for domestic, industrial, and...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ANSI B1.2-1974. 190p. This Standard provides essential specifications and dimensions for the gages used on Unified inch screw threads (UN and UNR thread form), and covers the specifications and dimensions for the thread gages and measuring equipment listed in Tables 1 and2.
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B1.3М-1992. Date of Issuance: October 12, 2007. 22 р. This Standard presents screw thread gaging systems suitable for determining the acceptability of UN, UNR, UNJ, M, and MJ screw threads on externally and internally threaded products. It establishes the criteria for screw thread...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME/ANSI B1.5-1988. Date of Issuance: December 6, 1999. 121 p. This Standard provides for two general applications of Acme threads: namely, general purpose and centralizing. The limits and tolerances in this Standard relate to single-start Acme threads and may be used, if considered...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B1.7М-1984. Date of Issuance: November 17, 2006. 38 р. The purpose of this Standard is to establish a uniform practice for standard screw threads with regard to the following: (a) screw thread nomenclature (b) letter symbols for the designating features of a screw thread for use...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B107.11M-1993. Date of Issuance: October 31, 2002. 16p. This Standard covers the dimensional and functional characteristics of pliers suitable for cutting wire. Pliers shall have cutting edges diagonal to or at right angles to their longitudinal axis.
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B107.17M-1985 (R1991). Date of Issuance: December 31, 1998. 15p. This Standard establishes final inspection gage sizes for wrench openings, and spark plug wrench openings for inch and metric sizes. This Standard does not cover every available size, but only those most commonly...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B107.23M-1991. Date of Issuance: August 28, 1997. 15p. This Standard is intended to cover the general dimensional and functional characteristics of adjustable joint and slip joint pliers.
An American National Standard. The American Society of Mechanical Engineers (ASME). Consolidation of ASME B107.47M and B107.48M. Dale of Issuance: September 15, 2005. 16p. This Standard provides performance and safety requirements for handheld and handled metal chisels. punches. and rift pins. Chisels are intended specifically for use in cutting and shaping metal objects. Punches...
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ANSI B16.11-2009. Date of Issuance: January 30, 2012. 32 p. This Standard covers ratings, dimensions, tolerances, marking, and material requirements for forged fittings, both socket-welding and threaded, as illustrated in Tables 1 through 5 and Tables I-1 through I-5, inclusive.
An American National Standard. The American Society of Mechanical Engineers (ASME). Revision of ASME B16.1-1998. Date of Issuance: August 31, 2006. 70p. This Standard covers Classes 25, 125, and 250 Gray Iron Pipe Flanges and Flanged Fittings. It includes: (a) pressure-temperature ratings; (b) sizes and method of designating openings of reducing fittings; (c) marking; (d)...