American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3722 – 82 (1999). 2 p. This specification covers dry and wet ground naturally occurring iron oxide, dry and wet ground calcined naturally occurring iron oxide, and mixtures of these with...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3721 – 83 (1999). 2 p. This specification covers synthetic red iron oxide for use in paints and coatings manufactured by any of the following: 1 Calcination of iron salts. 2 Precipitation...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1939 . Last previous edition approved in 2000 as D 520 – 00. 2 p. This specification covers three types of zinc dust, for use as a pigment in paints. The values stated in SI units are to be regarded as the standard. The values given in...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1938. Last previous edition approved in 2003 as D 509 – 03. 3 p. These test methods cover procedures for sampling and determining the grade of rosin delivered in commercial bags, barrels, drums or in molten form. Although developed for rosin, these...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1938. Last previous edition approved in 2000 as D 476 – 00. 3 p. This classification describes seven types of dry pigmentary titanium dioxide products, grouped by composition, typical end use application, and some performance properties....
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published January 2006. Originally approved in 1937. Last previous edition approved in 2001 as D 465 – 01. 4 p. These test methods are intended for determining the acid number of naval store products as defined in Terminology D 804 including tall oil products, wood and gum rosin, and other...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published January 2006. Originally approved in 1937. Last previous edition approved in 1999 as D 464 – 95 (1999). 3 p. These test methods cover the determination of the saponification number of tall oil and products obtained by the fractionation of tall oil such as rosin, fatty acids and...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1927. Last previous edition approved in 1999 as D 263 – 75 (1999). 2 p. This specification covers the dry pigment commercially known as chrome oxide green. The values stated in SI units are to be regarded as the standard. The values given in...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1924. Last previous edition approved in 1999 as D 210 – 81a (1999). 2 p. This specification covers the pigment commercially known as bone black, ivory black, or drop black. The pigment may be purchased in the dry form or as an aqueous dispersion....
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1921. Last previous edition approved in 1999 as D 85 – 87 (1999). 2 p. This specification covers ferrous earthy pigment included under the general term ochre. The pigment may be purchased in the dry form.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1917. Last previous edition approved in 1999 as D 50 – 90 (1999). 5 p. These test methods cover procedures for the chemical analysis of yellow, orange, red, and brown pigments containing iron and manganese. The test methods apply specifically...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. 2 p. This practice covers the ability of a latex paint film to resist staining caused by the leaching of water-soluble materials when contacted with water shortly after application. Water staining is attributed to the leaching of surfactants or other water-soluble...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published September 2005. 3 p. This test method covers the laboratory procedure for determining the relative mileage of news inks on newsprint. The test method utilizes a proofing press, analytical balance and a reflection densitometer.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published September 2005. 15 p. This terminology standard covers terms used in the description of printing inks, printing materials, and printing processes. This terminology standard does not include definitions related to Print Problems (see Terminology D 6488).
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. 5 p. This guide covers procedures for establishing a program to monitor the performance of Coating Service Level III lining (and coating) systems in operating nuclear power plants. Monitoring is an ongoing process of evaluating the condition of the in-service lining...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005, 2005. Published July 2005. 3 p. This test method covers the procedure for determining the specular gloss of printed matter. This test is applicable to prints on any flat substrate including paper, paperboard, metallic foil and plastic produced by any printing process, either in the...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. 3 p. This guide delineates recommendations for development of procedures and criteria for designation of personnel as a Nuclear Coatings Specialist involved in work in nuclear facilities. The Nuclear Coatings Specialist is responsible for the technical aspects of...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. 4 p. This guide describes procedures for the application of brush or roller, or both, applied paint films to sealed wallboard for evaluating application properties. Because both the application and panel evaluation are subjective, this guide should be used only for...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 2003. Last previous edition approved in 2003 as D 6990 – 03. 12 p. This practice establishes a practice for evaluating degree of biofouling settlement on and physical performance of marine coating systems when panels coated with such coating...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 2000. Last previous edition approved in 2000 as D 6531 – 00. 3 p. This test method covers the procedure for determining the relative tinting strength of waterbased ink systems using a computer-aided spectrophotometer. This test method is...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published December 2005. Originally approved in 1999. Last previous edition approved in 2004 as D 6488 – 04. 6 p. This terminology standard gives definitions for problems that develop with printed matter as a result of deficiencies in the ink, substrate, press, or combinations thereof....
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1999. Last previous edition approved in 2001 as D 6486 – 01. 3 p. This practice covers the protocol for vehicle service exposure testing of automotive coatings. Such exposure testing is valuable for the verification of the performance of automotive...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1999. Last previous edition approved in 2003 as D 6442 - 03. 10 p. This test method covers the laboratory determination of the rate at which copper is released from an antifouling coating in substitute ocean water. The practical limits for...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1999. Last previous edition approved in 2000 as D 6419 – 00. 3 p. This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at...
American Society for Testing and Materials (ASTM). Current edition approved July 1 2005. Published August 2005. Originally approved in 1999. Last previous edition approved in 1999 as D 6386 – 99. 4 p. This practice describes methods of preparing surfaces of new and weathered hot-dip galvanized steel for painting. Hot-dip galvanized steel is produced by the immersion of fabricated...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1995. Last previous edition approved in 1999 as D 5724 – 99. 8 p. This specification establishes requirements for composition, physical properties, performance, and labeling of gouache paints. This specification covers pigments, vehicles, and...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1994. Last previous edition approved in 2000 as D 5618 – 94 (2000). 2 p. This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1993. Last previous edition approved in 2001 as D 5286 – 01. 5 p. These test methods cover the determination of the transfer efficiency of spray-applied coatings under general plant conditions. Transfer efficiency is the ratio of paint solids...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published April 2005. Originally approved in 1991. Last previous edition approved in 2005 as D 5163 – 05. 4 p. This guide covers procedures for establishing a program to monitor the performance of Coating Service Level I coating systems in operating nuclear power plants. Monitoring is an on...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1990. Last previous edition approved in 2005 as D 5098 – 05. 8 p. This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ acrylic emulsion paints. This specification covers...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1990. Last previous edition approved in 1999 as D 5067 - 99. 6 p. This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ watercolor paints. This specification covers pigments,...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1990. Last previous edition approved in 2001 as D 5066 – 91 (2001). 5 p. This test method covers procedures for determination of the transfer efficiency (using a weight method) under production conditions for in-plant spray application of automotive...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1991. Last previous edition approved in 2003 as D 5010 – 03. 7 p. This guide covers a list of test methods, practices, and specifications that can be used for the testing and evaluation of printing inks, printed ink films, and substrates used in...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1996. Last previous edition approved in 2002 as D 5009 – 02. 4 p. This test method covers the evaluation and comparison of the transfer efficiency of spray-applied coatings under controlled laboratory conditions. This test method has been shown...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1987. Last previous edition approved in 2001 as D 4712 – 97a (2001). 8 p. This guide covers the selection and use of procedures for testing water-reducible coatings, both pigmented and clear, utilizing synthetic latices, synthetic resin emulsions,...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1995. Last previous edition approved in 2002 as D 4446 – 02. 4 p. s test method is designed to evaluate the effectiveness of water-repellent compositions for retarding dimensional changes in coated wood submerged in water. It can also be used to...
American Society for Testing and Materials (ASTM). Current edition approved July 1, approved in 1999 as D 4302 – 99. 9 p. This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ oil, resin-oil, and alkyd paints. This specification covers pigments, vehicles, and additives. Requirements are included for pigment...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4263 – 83 (1999). 2 p. This test method is used to indicate the presence of moisture in concrete. The values stated in inch-pound units are to be regarded as the standard. The values given...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4262 – 83 (1999). 2 p. This test method covers procedures for determining the acidity or alkalinity of concrete surfaces prepared by chemical cleaning or etching prior to coating.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published June 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4260 – 88 (1999). 3 p. This practice covers surface preparation of concrete to prepare the surface prior to the application of coatings. This practice is intended to alter the surface profile of...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4258 – 83 (1999). 2 p. This practice includes surface cleaning of concrete to remove grease, dirt, and loose material prior to the application of coatings. Procedures include broom cleaning,...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1983. Last previous edition approved in 2001 as D 4236 – 94 (2001). 5 p. This practice describes a procedure for developing precautionary labels for art materials and provides hazard and precautionary statements based upon knowledge that exists in...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4228 – 99. 3 p. This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4227 – 99. 3 p. This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1981. Last previous edition approved in 1999 as D 4040 – 99. 9.p This test method covers the procedure for determining the falling-rod viscosity and degree of non-Newtonian behavior of printing inks, vehicles, and similar liquids that are...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1980. Last previous edition approved in 2000 as D 3928 – 00a. 3 p. This test method covers the determination of the uniformity of gloss or sheen of a paint applied by brush to a test panel simulating an interior wall section. Variations in gloss or...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1978. Last previous edition approved in 2001 as D 3732 – 82 (2001). 2 p. This practice applies to all coatings cured by ultraviolet energy. The values stated in SI units are to be regarded as standard. No other units of measurement are included...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1982. Last previous edition approved in 2001 as D 3260 – 01. 2 p. This test method covers the evaluation of the mortar and acid resistance of clear protective coating factory applied to extruded aluminum substrates. The values stated in SI units...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1974. Last previous edition approved in 2001 as D 3322 – 82 (2001). 4 p. This practice covers the selection and use of procedures for testing primers and primer surfacers. The test methods included are listed in Table 1. The values stated in SI...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1972. Last previous edition approved in 2001 as D 3133 – 01. 3 p. This test method covers the quantitative determination of the content of cellulose nitrate (also known as nitrocellulose) in lacquers containing alkyd resins. The values stated in...