Всероссийский научно-исследовательский и проектно-конструкторский институт нефтяного машиностроения (ОАО «ВНИИнефтемаш»). 2004. 24 стр. Настоящий альбом распространяется на сдвоенные аппараты теплообменные кожухотрубчатые с плавающей головкой: теплообменники «Т», холодильники «Х», конденсаторы «К» типа «П» и кожухотрубчатые с U-образными трубами: теплообменники «Т» типа «U» и их...
ДзержинскНИИХиммаш. 1990. Взамен ОСТ 26-01-1243-81. 47 стр. С изменением №2 от 01.03.2000г. Настоящий альбом распространяется на уплотнения валов для аппаратов с перемешивающими устройствами, предназначенными для работы при давлении от остаточного 0.00066 Мпа (5 мм рт. ст.) до избыточного 3.2 Мпа ( 32 кгс/м2).
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1997. Last previous edition approved in 2005 as G 155 – 05. 11 p. This practice covers the basic principles and operating procedures for using xenon arc light and water apparatus intended to reproduce the weathering effects that occur when...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2006. Published April 2007. Originally approved in 1997. Last previous edition approved in 2000 as G 151 – 00. 15 p. This practice provides general procedures to be used when exposing nonmetallic materials in accelerated test devices that use laboratory light sources. Detailed information...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. 17 p. These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury. These test methods may be used to test for compliance to minimum performance requirements in established safety standards
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 2002. Last previous edition approved in 2003 as F 2215 – 03. 35 p. This specification covers requirements for ferrous and nonferrous inch balls. The balls covered in this specification are intended for use in bearings, bearing applications, check...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2011. Published September 2011. Originally approved in 2002. Last previous edition approved in 2009 as F2170 - 09. 6 p. This test method covers the quantitative determination of percent relative humidity in concrete slabs for field or laboratory tests.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published December 2006. Originally approved in 2001. Last previous edition approved in 2003 as F 2094 – 03a. 8 p. This specification covers the establishment of the basic quality, physical/mechanical property, and test requirements for silicon nitride balls Classes I, II, and III to be used...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 2000. Last previous edition approved in 2000 as F 1941M – 00. 11 p. This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with metric screw threads. It specifies coating...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1998. Last previous edition approved in 2000 as F 1941 – 00. 10 p. This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with unified inch screw threads. It specifies...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1998. Last previous approved in 2004 as F 1852–04a. 8 p. This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as “sets.” These assemblies are capable of developing a minimum...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published September 2007. Originally approved in 1997. Last previous edition approved in 2007 as F 1789 – 07a. 12 p. This terminology standard provides a compilation of definitions for terminology used for mechanical fasteners. Terms in this terminology are organized alphabetically. In...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2005. Published January 2006. Originally approved in 1995. Last previous edition approved in 2003 as F 1667 – 03. 41 p. This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Fasteners described in this specification are driven by hand tool, power...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1994. Last previous edition approved in 2004 as F 1554 – 04. 9 p. This specification covers straight and bent, headed and headless, carbon, carbon boron, alloy, or high-strength lowalloy steel anchor bolts (also known as anchor rods). The anchor...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2007. Published July 2007. Originally approved in 1994. Last previous edition approved in 2002 as F 1503 – 02. 4 p. This practice covers provision of a proper method for determining process capability for new or existing machine processes. It is recommended that available statistical software be...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1992. Last previous edition approved in 1999 as F 1428 – 92 (1999). 3 p. This specification covers the basic requirements for a corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1989. Last previous edition approved in 2001 as F 1267 – 01. 7 p. This specification covers expanded metal. Expanded metal covered by this specification is intended for a variety of applications. The values stated in inch-pound units are to be...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally
approved in 1988. Last previous edition approved in 2000 as F 1137-00. 2 p. This specification covers the basic requirements for seven grades of corrosion protection for fasteners. Grade 0A consists of a zinc phosphate coating with no additional sealer (dry),...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published November 2006. Originally approved in 1994. Last previous edition approved in 2004 as F 959M – 04. 5 p. This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2007. Published April 2007. Originally approved in 1985. Last previous edition approved in 2006 as F 959 – 06. 4 p. This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2007. Published July 2007. Originally approved in 1984. Last previous edition approved in 2001 as F 901 – 01. 4 p. This specification covers aluminum structural bolts and nuts for use in the construction of aluminum transmission towers, substations, and similar aluminum structures. Diameters of...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1983. Last previous edition approved in 2004 as F 844 – 04. 4 p. This specification covers round and miscellaneous shape steel plain (flat) washers furnished in an unhardened condition. The washers are intended for general use bolt, nut, and...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2007. Published December 2007. Originally approved in 1983. Last previous edition approved in 2003 as F 812/F 812M – 03. 5 p. This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2007. Published December 2007. Originally approved in 1982. Last previous edition approved in 2006 as F 788/F 788M – 06. 6 p. This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1982. Last previous edition approved in 2005 as F 747 - 05. 4 p. This Standard Covers Terminology Relating to Amusement Rides and Devices
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1987. Last previous edition approved in 2005 as F 606M – 05. 15 p. These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of metric externally and internally threaded fasteners,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1979. Last previous edition approved in 2006 as F 606 – 06. 15 p. These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct...
American Society for Tesing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1978. Last previous edition approved in 2001 as F 592 – 84 (2001). 5 p. The terms included in these definitions are listed in alphabetical order to facilitate quick reference. They are intended to apply to collated and cohered nails, staples, and pins...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1977. Last previous edition approved in 2001 as F 547 – 01. 15 p. The terms included in these definitions are listed in alphabetical order under six headings to facilitate quick reference. They are intended to apply to metal nails. Some of these...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May11 p. This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications. Unless otherwise...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1976. Last previous edition approved in 2005 as F 468 – 05a. 11 p. This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs 0.250 to 1.500 in. inclusive in diameter manufactured from a number of...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1979. Last previous edition approved in 2006 as F 467M – 06. 10 p. This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1976. Last previous edition approved in 2006 as F 467 – 06. 10 p. This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1976. Last previous edition approved in 2004 as F 436 – 04. 6 p. This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1⁄4 through 4...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2009. Published June 2009. Originally approved in 1975. Last previous edition approved in 2007 as F412 - 07. 16 p. This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1966. Last previous edition approved in 2004 as F 68 – 99 (2004). 6 p. This specification establishes the requirements for wrought and fabricated shapes made from Copper UNS2 No. C10100, conforming to the chemical requirements of Specification B...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published July 2011. Originally approved in 2002. Last previous edition approved in 2009 as C 1540-09a. 5 p. This specification covers the evaluating of the performance of heavy duty shielded couplings to join hubless cast iron soil pipe and fittings. Couplings covered by this standard...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. 25p. This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM:...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2013. Published January 2014. Originally approved in 1996. Last previous edition approved in 2011 as E1820 – 11. 54 p. This test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 15, 2013. Published February 2014. Originally approved in 1978. Last previous approved in 2013 as E647 – 13. 50 p. This test method covers the determination of fatigue crack growth rates from near-threshold to Kmax controlled instability. Results are expressed in terms of the crack-tip...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1974. Last previous edition approved in 2003 as E 527–83 (2003). 7 p. This practice (Note 1) covers a unified numbering system (UNS) for metals and alloys that have a “commercial standing” (see Note 2), and covers the procedure by which such...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2012. Published January 2013. Originally approved in 1970. Last previous edition approved in 2009 as E399 – 09. 33 p. This test method covers the determination of fracture toughness (KIc) of metallic materials under predominantly linear-elastic, plane-strain conditions using fatigue precracked...
Aмериканское Общество по Испытаниям и Материалам (ASTM). Текущее издание было утверждено 1 мая 2007. Опубликовано в июне 2007 года. Первоначально утверждено в 1953. Предпоследнее издание было утверждено в 2002 как D 1267 – 02. 4 стр. Данная методика предназначена для определения избыточного давления сжиженных нефтяных газов при температуре 37.8оС (100оF) до температуры анализа...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2009. Published August 2009. Originally approved in 1989. Last previous edition approved in 2007 as D4956 – 07. 11 p. This specification covers flexible, non-exposed glass bead lens and microprismatic, retroreflective sheeting designed for use on traffic control signs, delineators, barricades, and...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2010. Published June 2010. Originally approved in 1947. Last previous edition approved in 2007 as C216 – 07a. 13 p. This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. The property requirements of this...
American Society for Testing and Materials (ASTM). Current edition approved June l. 2009. Published June 2009. Originally approved in 1931. Last previous edition approved in 2008 as C 90-08. 4 p. This specification covers hollow and solid concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published November 2009. Originally approved in 1931. Last previous edition approved in 2006 as A135/A135M – 06. 9 p. This specification covers two grades of electric-resistance-welded steel pipe in NPS 2 to NPS 30 [DN 50 to DN 750] inclusive, with nominal (average) wall thickness up to 0.500...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1977. Last previous edition approved in 2001 as E 618 – 81 (2001). 11 p. This test method covers a production-type test for evaluating the machining performance of ferrous metals as they are used in single-spindle or multiple-spindle automatic screw...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published June 2011. 5 p. This test method applies to measuring plate deflections using a Portable Impulse Plate Load Test device. The method covers the measurement of deflection of the load plate rather than the deflection of the surface of the pavement or foundation layers (see Note 1).
American Society for Testing and Materials (ASTM). Current edition approved Julu 1, 2007. Published July 2007. 1 p. This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using Flash Thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with...